If My Computer Fails During a Dive I Should: Step-by-Step Actions (2026)
If my computer fails during a dive I should follow a clear, safe sequence: stop, gas-check, ascend with a plan. Here is what to do on reef and shore dives.
Updated November 2026
If my computer fails during a dive I should stop descending, check my depth and time with my backup, and begin a controlled ascent that follows my dive plan. A failed dive computer is a manageable problem when you have a backup and a routine. This guide walks through what to do underwater, how to ascend safely, and how to prevent the problem from happening in the first place.
Stop, Assess and Stay Calm
The first few seconds matter most. Stop moving down, hold a neutral position, and check that your buddy is in sight. Look at the screen once more to confirm it is truly blank or frozen rather than showing a low-battery warning you can still read.
Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).
Next, read your backup. Most divers carry a second computer or a submersible pressure gauge and a depth gauge with a dive timer. Note your current depth, your elapsed bottom time, and your remaining gas pressure before you do anything else.
Switch to Your Backup and Plan the Ascent
Once you have your backup readings, decide how you will ascend. If you are still near your planned maximum depth and have a clear dive plan, follow the depth-and-time profile you already set before the dive. If you have no reliable depth or time information, treat the dive as one that requires a conservative approach. If you want more background, see Why Do Dive Goggles Anti Fog Fail? 6 Causes and Fixes.
- Ascend at a rate no faster than the speed your computer or backup timer normally displays, usually around 9 meters (30 feet) per minute as a common reference.
- Make a safety stop at about 5 meters (15 feet) for at least 3 minutes, even if your computer does not tell you to.
- If you are unsure how deep you have gone or how long you have stayed, plan a longer stop and ascend slowly.
- Watch your gas. Begin your ascent with enough air to cover the stop, the ascent, and a reserve for emergencies.
Ascend Safely Using a Simple Checklist
Use this sequence every time, so it becomes automatic:
- Signal your buddy that you are ascending and confirm they acknowledge.
- Check your backup depth gauge and timer at the start of the ascent.
- Hold your ascent rate steady, watching your depth gauge rather than rushing.
- Stop at 5 meters (15 feet) for the safety stop, reading your backup as you hold.
- Surface with a safe reserve of gas, and inflate your BCD only as needed to stay controlled.
Prevent Computer Failure Before You Dive
Most failures are preventable. Before each dive, check battery level, confirm the computer powers on, and verify it reads depth correctly on the surface. Keep a spare battery or charger if your model uses one. Rinse and dry the unit after every dive, and inspect the O-rings and transmitter connections. For dive computers that connect to a regulator, follow the setup steps in our guide on Scuba Regulator with Dive Computer: 6 Steps to Match and Set Up so the transmitter and display are paired correctly before you enter the water.
If your computer is built into your mask, a little extra care goes a long way. Our overview of Oceanic Dive Mask Computer: 5 Steps to Choose and Set Up for Reef Diving covers pairing and display checks that prevent surprises underwater.
Common Mistakes
- Continuing the dive without a backup depth or time reference.
- Ascending quickly because the computer went blank, which raises the risk of decompression problems.
- Skipping the safety stop when you have no computer data to confirm your profile.
- Ignoring your gas reserve while troubleshooting the computer.
- Neglecting pre-dive checks, so the failure happens on the first deep dive of the day.
Recommended gear
A backup depth gauge and timer is the most useful item for this situation, since it gives you readings that do not depend on the primary computer. View on Amazon
A spare dive computer battery or a compact dive computer charger helps you avoid the most common cause of failure on multi-day trips. View on Amazon
A small slate or wrist-mounted log lets you note depth and time during the dive if you need to track the profile by hand. View on Amazon
FAQ
Can I keep diving if my computer stops working?
You should end the dive and ascend with your backup readings rather than continue deeper. Continuing without reliable depth or time data increases your decompression risk.
How slowly should I ascend without a computer?
Many divers use about 9 meters (30 feet) per minute as a reference ascent rate, with a 3-minute safety stop at 5 meters (15 feet). Confirm the rate in your training materials and your agency’s guidance.
Should I see a doctor after a dive where my computer failed?
If you feel any symptoms such as joint pain, numbness, unusual fatigue, or dizziness after surfacing, seek medical attention right away and mention the dive profile. Consult a dive medicine professional for advice specific to your situation.
Conclusion
If my computer fails during a dive I should stop, switch to my backup readings, and ascend slowly with a safety stop. A short routine and a reliable backup turn a potential emergency into a controlled end to the dive. Build the checklist into your pre-dive habits so it becomes second nature.
Related reading
Ready to choose one?
