Cressi Leonardo Dive Computer Battery: Replacement Steps and Tips
Learn how to replace the cressi leonardo dive computer battery safely, what to check before you start, and how to keep your dive computer reliable on the reef.
Updated November 2026
A cressi leonardo dive computer battery swap is a small job that keeps your computer reading depth, time and no-decompression limits accurately. This guide covers how to tell when the battery is failing, what you need on hand, and how to replace it without compromising the housing seal. Consult the manufacturer’s manual or an authorized service center if anything about the procedure is unclear.
Signs the Battery Is Running Low
Most dive computers give warning before they quit, and the Leonardo is no exception. Watch for a dim or flickering display, slow button response, or a low-battery icon that appears between dives. Some owners notice the unit resetting or losing its surface interval memory, which is a strong sign the cell is nearing the end of its life. Replace the battery at the first clear warning rather than waiting for a failure on a dive.
Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).
Preparing for the Battery Replacement
Work in a clean, dry area away from sand and salt water. Keep the O-ring and the housing surfaces free of debris, since a single grain of grit on the seal can cause a leak on your next dive. Before opening anything, confirm the battery type printed in the manual or on the battery compartment, and buy a matching replacement rather than an approximate substitute.
How to Replace the Battery Step by Step
- Rinse the computer in fresh water and dry it thoroughly.
- Lay the unit face down on a soft towel to protect the display.
- Unscrew the battery cover using the tool or coin slot specified in the manual, turning slowly to avoid stripping the threads.
- Remove the old battery and note its orientation, positive side up or down, before discarding it through proper battery recycling.
- Inspect the O-ring. If it is cracked, flattened, or dusty, replace it with a matching seal and apply a thin film of silicone lubricant.
- Insert the new battery in the same orientation, seat the cover, and tighten it to finger-tight plus a small turn with the tool. Do not overtighten.
- Power on the computer and confirm the date, time, and unit settings reset correctly, then run a leak check as described below.
Testing the Seal After Replacement
Before the first dive, let the computer sit in a bowl of fresh water for about 10 minutes and look for bubbles around the cover. Then check that the display and buttons respond normally. If anything looks wrong, remove the battery and repeat the seal inspection rather than diving with a questionable housing.
Common Mistakes and Tips
- Skipping the O-ring check, which is the most common cause of water entry after a battery change.
- Using a non-matching battery that fits physically but has a different voltage or chemistry.
- Overtightening the cover, which can crack the housing or damage the threads.
- Forgetting to re-check the settings, including units, altitude, and safety stop options.
- Storing the spare battery loose in a dive bag, where it can short against metal.
Recommended gear
A quality silicone lubricant helps keep the O-ring supple and seals clean. View on Amazon
A small set of replacement O-rings lets you swap a worn seal on the spot instead of guessing. View on Amazon
A soft microfiber towel protects the display during the battery change and keeps grit off the housing. View on Amazon
FAQ
How often should I change the battery in my cressi leonardo dive computer battery?
Battery life depends on how often you dive and how many logged hours you accumulate. Replace it when the low-battery warning appears or when the display becomes dim, rather than on a fixed schedule.
Can I use any battery that fits the battery for cressi leonardo dive computer?
Only use the battery type specified in the manual. A battery that fits physically but differs in voltage or chemistry can cause unreliable readings or damage the electronics.
Do I need to reset the computer after changing the battery?
Check the date, time, and unit settings after every replacement, since some models reset personal settings. Confirm your preferences before your next dive.
Conclusion
Replacing the cressi leonardo dive computer battery is quick when you match the battery type, inspect the O-ring, and tighten the cover correctly. Run a leak check before every dive that follows a battery change. For model-specific questions, check the manufacturer’s manual or a qualified dive shop.
Related reading
- Scuba Regulator with Dive Computer: 6 Steps to Match and Set Up
- Oceanic Dive Mask Computer: 5 Steps to Choose and Set Up for Reef Diving
- Genwiss Dive Light Battery Replacement: Step-by-Step Guide (2026)
- Cressi Pano 3 Scuba Dive Mask: Fit, Features and Who It Suits
Ready to choose one?
