We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

The First Step in Using My Dive Computer Is Setting It Up Correctly

The first step in using my dive computer is a quick pre-dive setup check. Learn what to verify, from battery and time to units and gas, before you descend.

Updated November 2026

The first step in using my dive computer is confirming it is set up for the dive you are about to make. Before you descend, you should check the battery, set your units and gas settings, and make sure the unit is in the correct mode for your dive. Doing this on the surface takes a few minutes and prevents most of the avoidable problems divers run into underwater.

Check the Battery and Power Status

Start by looking at the battery indicator on the display. Most dive computers show remaining charge on the home screen or in a settings menu. If the unit is rechargeable, charge it fully the night before. If it uses a replaceable battery, note the install date and replace it on the schedule the manufacturer specifies, not only when it fails. A computer that dies mid-dive leaves you without depth, time or decompression data.

Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).

Set Your Units, Time and Gas Mix

Next, confirm the basic settings that affect every number the computer shows:

  • Units: Choose feet or meters and psi or bar. Mixing these up is a common source of confusion when reading a tank pressure or depth.
  • Time and date: Set the correct local time so your dive log stays accurate.
  • Gas mix: If you dive nitrox, enter the oxygen percentage that matches the tank you filled. Check it against the fill label, not memory.
  • Altitude setting: If you dive at elevation, set the altitude mode so the decompression calculations are adjusted.

Select the Right Mode and Confirm the Pre-Dive Screen

Most computers offer air, nitrox and gauge modes. Air mode is the default for many recreational dives. Nitrox mode uses a different oxygen percentage and will show a different no-decompression limit. Gauge mode shows depth and time without decompression tracking, which is useful for some deep training or backup purposes. Select the mode that matches your plan.

Then look at the pre-dive screen. Many units show a no-decompression limit, a tissue loading indicator and a surface interval if you dived recently. If the computer shows a residual nitrogen warning from a previous dive, believe it and adjust your plan. The computer assumes your last dive was accurately logged, so make sure you did not switch it off or swap it between buddies without resetting.

Practical Pre-Dive Checklist

  1. Confirm battery charge is above the level you need for the day.
  2. Verify units (feet or meters, psi or bar).
  3. Verify the time and date.
  4. Match the gas mode and oxygen percentage to your tank.
  5. Set altitude mode if diving at elevation.
  6. Read the no-decompression limit and any surface interval warning.
  7. Confirm the computer is attached to your console or wrist and the display is visible.

Common Mistakes

  • Skipping the gas setting and assuming air mode is correct after a nitrox fill.
  • Ignoring a surface interval or residual nitrogen reading from an earlier dive.
  • Using a computer that has been shared without resetting its settings for the new diver.
  • Forgetting to charge the unit or check battery life before a multi-dive day.
  • Assuming the default units match what you are used to on a dive boat abroad.

A clear wrist-mounted or console-mounted computer with a readable display makes the pre-dive check far easier, especially in low light. A small waterproof logbook or the computer’s own logbook function helps you keep settings consistent across trips. A battery charger or spare battery kit can prevent a missed dive when the unit runs low.

FAQ

Do I need to set my dive computer before every dive?

Yes, at least check the settings before the first dive of the day. Confirm the gas mode, units and altitude setting, especially if you have changed tanks or locations.

What if my dive computer shows a surface interval warning?

Treat the warning as a real limit on your next dive. Plan a longer surface interval or a shallower profile, and follow your training agency’s guidance.

Where can I find the exact setup steps for my model?

Refer to the user manual that came with your computer or the manufacturer’s website. If you are unsure about any setting, consult a certified instructor before diving.

Conclusion

Checking battery, units, time, gas mode and the pre-dive screen takes only a few minutes on the surface. That short routine is the foundation for reading your computer accurately underwater. Make it a habit before every dive, and review your computer’s manual so you know exactly what each screen is telling you.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our scuba diving gear guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Scuba Lanai.