We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Use Cressi Leonardo Dive Computer: A Step-by-Step Guide for Divers

Learn how to use Cressi Leonardo dive computer, from first setup and mode selection to reading the display and logging dives safely on your next reef trip.

Updated November 2026

Learning how to use Cressi Leonardo dive computer comes down to three things: setting it up correctly before you dive, reading the display accurately underwater, and treating its no-decompression limits as firm rules. Once you work through the basics on land, the unit runs most of the planning for you. This guide covers the steps we follow on reef and shore dives, along with the mistakes that cause the most trouble.

Before You Dive: Setup and Checks

Start by confirming the battery is charged and the unit powers on cleanly. Check the manufacturer’s manual for the exact button sequence to enter setup on your model, since menu layouts vary between firmware versions. For background on the unit’s features, see Dive Computer Cressi Leonardo: Setup, Settings and Buying Tips for Reef Divers.

Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).

Set the core parameters before you leave the dock:

  • Units: metric or imperial, matching your depth and temperature habits.
  • Gas: air or nitrox, and the oxygen percentage if you are diving enriched air. Enter this exactly as you will breathe it.
  • Mode: air dive mode for standard dives, or a nitrox mode if your computer supports it for your mix.
  • Alarms: depth and time alarms at values you will actually respect.

For a full walkthrough of the modes and menus, the Cressi Leonardo Dive Computer Manual: Setup, Modes and Key Settings Explained article is a useful companion.

Step-by-Step: Using the Computer on a Dive

  1. Power on and check status. Confirm the unit is active and that the time, battery indicator and mode are correct.
  2. Start the dive. Most units begin logging automatically once they sense water and depth. Wait for the dive screen before descending.
  3. Monitor depth, time and no-deco limit. Read the depth and remaining no-decompression time at each check, not just at the start.
  4. Watch the ascent guidance. If the unit shows a safety stop prompt, follow it. A typical recreational safety stop is held at about 15 to 18 feet (5 to 6 meters) for three minutes, but follow the countdown your unit displays.
  5. Surface and review. After surfacing, check the surface interval and any warnings before your next dive.

Reading the Display Under Water

Practice reading the screen on land before you rely on it in the water. Know where depth, bottom time, no-deco time and tissue warnings sit on the display. The layout of each screen is covered in more detail in How to Read Dive Computer Displays: A Step-by-Step Guide for Divers.

Display item What to do
No-deco time falling fast Plan your ascent and reduce depth or time.
Ascent or safety stop prompt Follow it without delay.
Low battery icon End the dive soon and charge or replace the battery before the next one.

Post-Dive Care and Battery Management

Rinse the unit in fresh water after every dive and keep the buttons clean so they respond reliably. Battery life drops with cold, repeated use and age, so watch the indicator closely. If you need to swap the cell, follow the steps in Cressi Leonardo Dive Computer Battery: Replacement Steps and Tips.

Common Mistakes

  • Leaving the gas mix at the factory default when you are diving nitrox.
  • Ignoring a safety stop prompt because the dive feels easy.
  • Skipping the surface interval check before a repetitive dive.
  • Letting the battery run low mid-trip without a spare plan.
  • Assuming the computer replaces training. It only shows what you feed it and what it measures.

A dive computer works best when it is mounted securely and kept accessible. A console mount or wrist strap keeps the display visible at eye level during the dive.

  • A spare battery kit for the Cressi Leonardo, so a dead cell does not end your trip early. View on Amazon
  • A soft silicone cover to protect the buttons and screen from abrasion on rough shore entries. View on Amazon

FAQ

Do I need to set up the Cressi Leonardo before every dive?

You only need to change settings when your gas mix, units or alarms change. Confirm the mode and gas on the status screen before each dive.

What should I do if the computer shows a safety stop?

Follow the countdown and hold your depth until it clears. Treat the prompt as a required step, not an optional one.

Can the computer replace dive training?

No. It helps you track depth and time, but it cannot teach planning, buoyancy or emergency procedures. Consult a certified instructor for training specific to your diving.

Conclusion

Set up your gas, units and alarms before you leave the dock, then check the display at regular intervals underwater. Treat every safety stop prompt as a rule and review the unit after each dive. For specific medical or decompression questions, consult a qualified dive professional.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our scuba diving gear guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Scuba Lanai.