Sherwood The Source Dive Computer Manual: Setup, Modes and Key Settings
Find the Sherwood The Source dive computer manual explained: where to get it, how to set up the unit, read its display and avoid common mistakes on reef dives.
Updated November 2026
The Sherwood The Source dive computer manual is the reference you need before your first dive with the unit. This guide shows you how to find the right manual, what to check during setup, and how to read the core screens so you can plan a safe reef dive. It does not replace the printed or PDF manual, which is the authoritative source for your exact firmware.
Finding the Right Sherwood The Source Manual
Start with the manufacturer. Sherwood publishes manuals for its dive computers, and the best copy is the one listed for your model name and firmware version. Many owners find that the manual packed with the unit covers the same material as the online PDF, but the online version is easier to search when you are planning a dive on your phone.
Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).
- Confirm the model name printed on the back or inside the battery compartment.
- Check the manual’s revision date against what your computer shows in its information screen.
- Save a PDF copy to your phone so you can read it offline at the dive site.
Setup Steps Before Your First Dive
Set the computer up at home, not on the boat. Most of the settings that matter for a reef dive take only a few minutes, and fixing them in a hurry leads to mistakes.
- Set the date and time so your dive log timestamps are correct.
- Choose your unit system, meters or feet, and confirm the depth and temperature readings.
- Set your altitude mode if you dive above sea level. Skipping this changes the no-decompression limits.
- Select your gas mix if the unit offers nitrox settings, and enter your oxygen percentage carefully.
- Review the alarm settings for maximum depth, ascent rate and dive time, and leave them enabled.
- Check the battery level before you pack the unit. A low battery can shut the computer off mid-dive.
Reading the Display During a Dive
Once you are in the water, focus on three readings: current depth, no-decompression time remaining and ascent rate. Practice reading them on the surface first, so you know where each value sits on the screen without searching for it.
| Screen item | What to watch |
|---|---|
| Depth | Stay within the depth you planned for the reef profile. |
| No-deco time | Plan your ascent with a margin, not at the exact limit. |
| Ascent rate | Slow down when the alarm sounds, and make a safety stop when the unit prompts you. |
| Tank pressure | Only shown if you have a transmitter fitted. Confirm this before you buy an integrated unit. |
If you are comparing features across models, the Suunto Air-Integrated Dive Computer: Setup, Tips and Buying Guide article covers how air integration changes the display. For a broader setup routine, see Using a Dive Computer: A Step-by-Step Guide for Reef Divers.
Common Mistakes to Avoid
- Diving without checking the altitude setting when you travel to higher ground.
- Ignoring the battery warning and assuming the unit will last the whole trip.
- Changing settings between dives without rechecking the no-deco limits.
- Relying on memory for the ascent rate instead of watching the alarm.
- Skipping the manual because the unit feels familiar from another brand.
Recommended gear
A spare battery and a protective case help keep the unit ready for every dive. A simple wrist strap or console mount keeps the screen in view during the dive.
- Spare battery for the same model, so you can swap it on the boat if needed. View on Amazon
- Protective silicone boot to guard the screen and buttons from knocks on the reef. View on Amazon
- Wrist strap or console mount so the display stays in your line of sight. View on Amazon
FAQ
Where can I download the Sherwood The Source manual?
Check the Sherwood website for the manual listed under your model name. Confirm the revision date matches the firmware shown on your unit.
Do I need to set the altitude mode every trip?
Yes, if the dive site is at a different elevation from your last dive. Setting the wrong altitude can change the no-decompression limits.
Is the manual enough to plan a dive safely?
The manual explains how the unit works, but it does not replace dive training or a professional’s advice. Consult a certified instructor before diving with any new computer.
Conclusion
Read the manual for your exact model, set up the unit at home and practice reading the display before you enter the water. Keep alarms on, check the battery and plan your ascent with a margin. A few minutes of preparation makes every reef dive easier to manage.
Related reading
Ready to choose one?
