Mares Dive Computer Puck Pro Manual: Setup and Key Functions Explained
Find the mares dive computer puck pro manual essentials: setup steps, display modes, key settings and where to get the official manual before your next dive.
Updated November 2026
The mares dive computer puck pro manual is the printed guide that explains how to set up, read and maintain the Puck Pro before you dive with it. This article walks through what the manual covers, how to work through it in the right order, and where to find the current official version. You will leave knowing which sections matter most for a first dive and which settings to check before you get in the water.
Find the Right Mares Puck Pro Manual
Mares publishes manuals for its dive computers, and the Puck Pro line has had more than one revision. Check the official Mares website for the current PDF, and confirm the model name printed on the back of your unit matches the manual you download. Keep a copy on your phone or in your dive bag so you can reference it on a boat without digging through paperwork.
Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).
Set Up the Puck Pro Before Your First Dive
Most of the setup work happens on land. Work through the manual in this order:
- Install or confirm the battery and check that the display powers on and shows the correct time and date.
- Set units (metric or imperial) for depth, temperature and altitude to match how you plan to read them.
- Enter your alarm thresholds for maximum depth, dive time and ascent rate, using the defaults in the manual as a starting point.
- Set your gas mix if your model supports it, and confirm the oxygen percentage before any nitrox dive.
- Run a surface check: power up, cycle through each screen and confirm nothing is flagged.
Understand the Display Modes and Key Functions
The manual groups screens into dive, surface and logbook modes. Learn the button sequence for each mode while you are still on dry land, because you will not want to decode it at 15 meters. Pay particular attention to the sections on no-decompression limits, safety stops and the ascent rate indicator, since these drive your decisions during the dive.
| Manual section | What to look for |
|---|---|
| Setup and units | Metric or imperial, time format, date |
| Alarms | Depth, time and ascent rate thresholds |
| Dive mode | Current depth, NDL, tank pressure if connected |
| Logbook | How dives are stored and downloaded |
| Care and battery | Rinsing, storage temperature, replacement interval |
Plan Care and Battery Checks
The manual’s care section covers rinsing with fresh water after every dive, avoiding hard impacts and storing the unit away from direct heat. It also lists battery replacement intervals and recommends a seal and O-ring check at the same time. Follow those steps exactly, and use only the battery type the manual specifies. For a detailed walkthrough, see Mares Dive Computer Battery Replacement: Step-by-Step Guide (2026).
Setup tips for travel
If you dive in a different time zone, adjust the clock before you leave home so logbook entries stay consistent. Recheck altitude settings when you dive at a lake or inland site.
Common Mistakes
- Skipping the surface check and discovering a setting problem underwater.
- Using a manual for a different model number from the Puck Pro line.
- Leaving alarm thresholds at factory defaults without reviewing them for your diving.
- Storing the unit in a hot car, which can affect the battery and display.
- Never reading the sections on ascent rate and safety stops before a first dive.
Recommended gear
A small waterproof notebook helps you record settings you change from the defaults, so you can restore them quickly after a battery swap. View on Amazon
A silicone cover or protective case can reduce impact damage on the boat and on shore entries. View on Amazon
FAQ
Where can I find the official Mares Puck Pro manual?
Download the current PDF from the official Mares website, and match it to the exact model name on your unit. Older printed manuals may not cover later firmware or features.
Do I need to read the whole manual before diving?
Read the setup, alarm, dive mode and care sections at minimum. Those cover what you need for a safe first dive.
Should I consult a professional about dive computer settings?
Yes. If you are unsure about decompression settings, altitude adjustments or any error message, consult a certified instructor or the manufacturer before diving.
Conclusion
The Puck Pro manual rewards a careful read before your first dive. Complete the setup steps on land, learn the display modes and check the care and battery sections. Keep the official manual handy so you can confirm settings whenever something changes.
Related reading
- Mares Puck Pro Plus Dive Computer: Setup, Use and Buying Tips
- Mares Dive Computer Puck Pro: Setup, Use and Care Tips
- Mares Nemo Dive Computer: Setup, Settings and Buying Tips for Reef Divers
- Does a Dive Computer with GPS Help on Reef Dives? Pros and Cons
- Dive Computer Mares Smart: Setup, Settings and Tips for Reef Dives
Ready to choose one?
