Mares Puck Pro Plus Dive Computer: Setup, Use and Buying Tips
Learn how the mares puck pro plus dive computer works, how to set it up and read it on the reef, plus buying tips for recreational divers.
Updated November 2026
The mares puck pro plus dive computer is a compact wrist-mounted unit that tracks depth, bottom time and no-decompression limits so you can plan and manage each dive. This guide walks through the basic setup, how to read the display during a reef dive, and what to check before you buy. Manufacturer manuals cover the full feature list, so treat this as a practical starting point rather than a replacement for the owner’s guide.
What You Need Before Your First Dive
Before you enter the water, gather the items that make setup and monitoring straightforward.
Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).
- The unit’s manual and any quick-start card from the box
- A fully charged battery, or a fresh battery if your model uses a replaceable cell
- A wrist strap or console mount sized to your arm or hose
- A logbook or app to record dives, plus a waterproof slate for backup notes
- Your dive buddy’s computer model, so you can compare readings and plan a matched profile
Setting Up the Mares Puck Pro Plus Dive Computer
Setup takes a few minutes, but it matters more than most divers expect. Enter your personal data and units first, then confirm the mode you plan to dive in.
- Power on the unit and set the date and time, which the logbook uses to sort dives.
- Choose metric or imperial units. Most recreational divers in the US work in feet and psi, so confirm the depth display matches what your briefing uses.
- Select air or nitrox mode. If you are using enriched air, enter the oxygen percentage exactly as stated on your tank label and analyze the gas before you dive.
- Check the alarm settings for depth, ascent rate and remaining no-decompression time. Leave the defaults unless your instructor or dive shop recommends changes.
- Run a short surface check to confirm the display, backlight and buttons respond correctly.
After setup, check the manual for the exact button sequence to enter surface intervals and to switch between dive modes. Button layouts vary slightly between firmware versions, so verify the steps against your own unit.
Reading the Display on a Reef Dive
On a reef dive, you will mostly glance at depth, bottom time and remaining no-decompression time. Keep the display in your line of sight, and build a habit of checking it at the same points in each dive, such as every few minutes or at each new depth. Ascend at a controlled rate, and pay attention to any ascent-rate warning. If the computer shows a safety stop prompt, follow it.
Be deliberate about deeper excursions. When you descend past your planned depth, the no-decompression limit drops quickly, so the computer shows less time available. Treat that number as a planning tool, not a target.
Buying Considerations
If you are still deciding whether this unit suits you, compare these points against your own diving:
| Factor | What to look for |
|---|---|
| Dive mode | Air only or air plus nitrox, depending on your certification plans |
| Display | Legibility at depth and in low light, especially for night dives |
| Battery | Replaceable versus rechargeable, and how easily you can service it |
| Mounting | Wrist versus console, based on how you prefer to monitor your dive |
| Logging | Whether the unit downloads dive data to your computer or app |
Check the seller’s listing for the exact firmware version and included accessories before you order.
Common Mistakes
- Leaving the computer on the boat or in a dive bag during the surface interval, then forgetting to reset the surface timer.
- Using the wrong oxygen percentage in nitrox mode.
- Ignoring ascent-rate warnings because the dive feels calm.
- Failing to check the battery before a trip.
- Diving with a computer that differs from your buddy’s without agreeing on a shared plan.
Recommended Gear
- A spare battery or charger matched to your model, so a dead unit does not end your trip. View on Amazon
- A wrist strap or console mount that keeps the unit in view without snagging on gear. View on Amazon
- A dive slate for noting surface intervals and gas mix as a backup record. View on Amazon
FAQ
Can I use the mares puck pro plus dive computer for nitrox diving?
Check whether your specific model supports nitrox mode, since features vary by version. If it does, enter the oxygen percentage from your tank label before the dive and confirm the setting during your gas analysis.
How do I know when to replace the battery?
Watch for a low-battery indicator on the display and replace it before a trip, not during one. Follow the manufacturer’s guidance on battery type and service.
Should I rely only on the computer for dive planning?
No. Use it alongside a dive table or planning software and your training. For questions about your personal dive limits or health, consult a dive professional or physician.
Conclusion
The mares puck pro plus dive computer is most useful when you set it up carefully, check it at regular intervals, and respect the limits it shows. Confirm the features you need before buying, and read the owner’s manual cover to cover. Keep a backup plan for gas, depth and time, and dive within your training.
Related reading
- Scuba Regulator with Dive Computer: 6 Steps to Match and Set Up
- Oceanic Dive Mask Computer: 5 Steps to Choose and Set Up for Reef Diving
- Scubapro Pro Ear 2026 Dive Mask: 3 Best Picks for Reef Divers (2026)
- Mares X-Vision Dive Mask: Fit, Seal and Buying Tips for Reef Divers
- Mares Trilastic 5mm Dive Boots: Fit, Warmth and Buying Tips
Ready to choose one?
