We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

SEAC Action HR Dive Computer: Setup, Reading and Buying Tips

Learn how to set up, read and use the seac action hr dive computer on reef dives, with settings checks, buying factors and common mistakes to avoid.

Updated November 2026

The seac action hr dive computer is a wrist-worn dive computer that tracks depth, time, ascent rate and no-decompression limits so you can plan and log each dive. This guide walks you through the initial setup, how to read the display during a dive, and what to check before you buy one used or new. Follow these steps and you will know what the computer is telling you before you descend.

Step 1: Set Up the Computer Before Your First Dive

Set the units, time and date before you enter the water. Most divers choose metric depths and a 24-hour clock, but the choice is yours as long as you know what the display shows. Confirm the battery level on the start screen and note how long the unit has been in service.

Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).

Next, check the water type setting. Salt water and fresh water produce different pressure readings, and a mismatch can throw off depth numbers by a noticeable margin. Set it to match where you are diving, and reset it if you move between locations.

Step 2: Learn the Display Before the Dive

Spend a few minutes on the surface reading each screen. Look for current depth, dive time, maximum depth, no-decompression time remaining and the ascent rate indicator. Practice switching between screens with the buttons while wearing gloves, since you may need to do this on a cold or rough dive.

  • Current depth and maximum depth
  • Elapsed dive time
  • No-decompression time remaining (NDL)
  • Ascent rate indicator
  • Surface interval and tissue loading

Step 3: Monitor the Computer Through the Dive

Check the computer at regular intervals, not just when something feels wrong. Glance at the NDL and depth at the start, every few minutes at your working depth, and before each ascent. If the ascent rate indicator flashes, slow down immediately and hold your ascent until the warning clears.

Keep your air supply in mind alongside the computer. Many divers pair the unit with a console or air-integrated setup so that tank pressure appears on the same screen. If you use a standalone computer, read your gauge at the same time intervals.

Step 4: Check the Computer After the Dive

Review the dive log and confirm your surface interval. Let the unit count down the required surface time before any repeat dive, and do not override warnings. Rinse the computer in fresh water and inspect the seals and buttons for sand or grit.

What to Check Before You Buy or Use a Used Unit

Factor What to look for
Battery Replacement method and how the unit reports low power
Display Readability in bright light and at night
Modes Air, nitrox and gauge options that match your diving
Manual Availability of the user guide and firmware information

For a broader comparison of wrist-worn units and how they fit different diving styles, see Wrist Mounted Dive Computer: A Step-by-Step Guide for Choosing and Using One and Scuba Diving Dive Computer: 6 Steps to Choose and Use One Safely.

Common Mistakes to Avoid

  • Skipping the water type setting, which affects depth readings.
  • Ignoring the ascent rate warning because the dive feels routine.
  • Diving with a low battery and assuming the unit will last the day.
  • Failing to reset the surface interval before a repeat dive.
  • Using the computer without first learning the buttons on land or at the surface.

A spare wrist strap or a protective boot can help keep the unit secure during rough shore entries. View on Amazon

A small dive slate keeps notes on settings and surface intervals handy if you prefer writing down what the computer shows. View on Amazon

A soft carry pouch protects the display from scratches in your gear bag. View on Amazon

FAQ

Can I use the seac action hr dive computer for nitrox diving?

Check the modes listed in the manual for your specific unit, since mode availability varies by version. If nitrox is supported, set the oxygen percentage before the dive and confirm it on the display.

How often should I replace the battery?

Battery life depends on use, temperature and the model, so follow the manufacturer’s replacement guidance. Have a qualified dive shop replace the battery and seals to keep the water seal intact.

What should I do if the computer shows an error during a dive?

End the dive safely by following your training agency’s procedures and your buddy’s guidance. Consult a professional dive instructor or the manufacturer before the next dive.

Conclusion

Set up the seac action hr dive computer correctly, learn the display on land, and check it throughout every dive. Review the log afterward and follow the surface interval before diving again. For questions about medical fitness or diving safety, consult a qualified professional.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our scuba diving gear guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Scuba Lanai.