Mares Icon HD Dive Computer: Setup, Settings and Buying Tips
Learn how to set up, configure and buy the Mares Icon HD dive computer, with practical settings, care steps and buying factors for reef and shore divers.
Updated November 2026
The Mares Icon HD dive computer is a wrist-mounted unit that tracks depth, time, decompression status and gas use for recreational dives. This guide walks you through the first-time setup, the settings worth checking before each dive, and the factors to weigh if you are deciding whether this model suits your diving. Use it alongside the manufacturer’s manual, which is the authoritative source for your exact firmware and features.
Step 1: Set Up Your Mares Icon HD Before the First Dive
Start with the basics on land. Charge the unit fully, then set the date, time and units. Most divers prefer metric for depth and temperature, but confirm which you want before you descend, because switching mid-trip causes confusion when you compare logs.
Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026). We also found Mares Nemo Wide Dive Computer Wrist Watch Manual: Setup and Use Guide useful on this point.
- Charge the unit until the battery reads full.
- Set the date, time and measurement units (metric or imperial).
- Confirm the gas mix setting if you plan to use nitrox.
- Check the alarm thresholds for maximum depth and ascent rate.
- Run a quick display and button test on the surface.
Step 2: Configure Dive Modes and Alarms
The Icon HD is built around a simple mode structure, so decide your settings before you enter the water. Set the gas mix to match your tank, usually air at 21 percent oxygen unless you have trained for enriched air. Keep the alarm thresholds conservative until you are comfortable with how the unit reacts during ascent and safety stops.
Review your no-decompression limit and the remaining time shown on the display at the surface. Many divers find it useful to memorize the screen layout during a surface check so they can read it quickly underwater.
Step 3: Use the Computer During Reef and Shore Dives
On a reef dive, the most useful readings are current depth, dive time, ascent rate and the no-decompression countdown. Glance at the display every few minutes rather than constantly, and always stay within the limits your training agency teaches. For shore dives, check that the unit is clearly visible on your wrist after you gear up and that the strap is snug over your wetsuit sleeve. If you dive with a buddy, agree on how you will share computer readings and when you will end the dive.
For a broader walkthrough of how these units fit into a dive plan, see Using a Dive Computer: A Step-by-Step Guide for Reef Divers. If you are comparing Mares models, Mares Puck Pro Plus Dive Computer: Setup, Use and Buying Tips covers a console-style alternative.
Step 4: Review Your Log and Care for the Unit
After each dive, download or review the log and note any alarms. Rinse the unit in fresh water, keep the buttons clean, and avoid storing it in direct sun. Replace the battery according to the manufacturer’s schedule, and have a qualified technician check the unit if the display fogs or buttons stop responding. Battery swaps should be done carefully to protect the seals; Mares Dive Computer Battery Replacement: Step-by-Step Guide (2026) describes the general process for the Mares line.
Common Mistakes to Avoid
- Skipping the surface check, which is when most setting errors are caught.
- Leaving the gas mix at the default when you dive a different blend.
- Ignoring a low battery warning before a trip.
- Rinsing the unit only once after a saltwater dive, which leaves salt on the buttons.
- Assuming the computer replaces your training. It supports your planning but does not substitute for it.
Recommended Gear
A dive computer works best when the rest of your kit keeps it accessible and protected.
- A wrist-mount accessory or spare strap keeps the unit secure over a thick wetsuit sleeve. View on Amazon
- A soft dive bag with a dedicated pocket protects the unit during transport between shore sites. View on Amazon
- A plastic dive computer case or cover shields the display from scratches on rocky entries. View on Amazon
FAQ
Does the Mares Icon HD work with nitrox?
Yes, most Mares computers in this class allow you to set a nitrox mix before the dive. Confirm the supported range in your manual, and make sure your setting matches the tank you are actually breathing from.
How often should I replace the battery?
Follow the schedule in the manufacturer’s documentation, and replace it sooner if the low-battery warning appears or the display dims. Have a qualified service provider handle the swap if you are unsure about the seals.
Is a wrist computer better than a console for reef diving?
A wrist unit is convenient for quick glances and gives you a clear view during reef dives. A console suits divers who want gauges and computer data in one place. Choose based on your comfort and how you usually dive.
Conclusion
Set up the Mares Icon HD carefully on land, check your gas and alarm settings at the surface, and review your log after every dive. Consistent habits matter more than any single feature. For personal dive planning and any questions about decompression, consult a qualified dive professional or your training agency.
Related reading
Ready to choose one?
