We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

How to Clean Scuba Regulator: A Step-by-Step Guide for Divers

Learn how to clean a scuba regulator at home with a freshwater rinse, gentle soak and proper drying. Simple steps to protect your regulator between dive trips.

Updated November 2026

Knowing how to clean a scuba regulator properly keeps salt, sand and bacteria from building up inside the first and second stages. This guide walks through a freshwater rinse, a gentle soak, correct drying and storage, so your regulator breathes easily on the next reef dive. Work slowly and keep the dust caps on whenever the regulator is not connected to a tank.

Rinse the Regulator Right After Every Dive

Salt crystals start forming within minutes of drying, so the first cleaning step happens on the boat or shore. Rinse the regulator with fresh water while keeping the first stage pointed downward, and let water run over the second stage mouthpiece and purge button. Avoid pressing the purge button under running water, because that can push grit into the valve seat.

Soak and Flush the Regulator Properly

Once a day, or at the end of a multi-dive trip, give the regulator a longer soak. Use a clean bucket of lukewarm fresh water and let the regulator sit for about 15 to 20 minutes, with the dust caps on and the hoses curled loosely. Some manufacturers recommend a mild regulator-safe cleaner for this step, so check the owner’s manual before using anything else. Never use household soaps, bleach, vinegar or alcohol, since these can damage seals and internal components.

Flushing the Second Stage and Hoses

  1. Hold the second stage with the mouthpiece facing down.
  2. Gently press the purge button several times while the freshwater flows through.
  3. Swish water through each hose by pouring it in from the low-pressure port end.
  4. Let the water drain fully before moving to the drying step.

Dry and Store the Regulator Safely

Hang the regulator in a shaded, well-ventilated spot with the first stage facing down so any remaining water drains out. Direct sun can degrade rubber hoses and O-rings over time, so avoid leaving gear on a sunny deck. Once fully dry, replace the dust caps and store the regulator loosely coiled, not kinked or pulled tight.

Checklist: Tools You Need to Clean a Scuba Regulator

  • A clean bucket or basin for freshwater soaking
  • Fresh, lukewarm tap or filtered water
  • A regulator-safe cleaner, only if the manufacturer approves it
  • Soft cloth or towel for wiping the outside
  • A shaded hanging spot with airflow
  • Clean dust caps for every port

Common Mistakes When Cleaning a Scuba Regulator

  • Leaving the regulator to dry in salt water, which leaves crystals in the valve
  • Pressing the purge button under a hard stream of water
  • Using vinegar, bleach or alcohol instead of mild cleaners approved by the manufacturer
  • Storing the regulator with the dust caps off
  • Skipping the annual service, which should be done by a certified technician

A dedicated regulator cleaning kit with a tight-fitting rinse hose makes flushing much easier than a garden hose. View on Amazon

A breathable mesh dive gear bag keeps the regulator out of the sun and away from sand while it dries. View on Amazon

A small bucket with a lid helps you soak the regulator without spilling freshwater all over the dock. View on Amazon

If you are also caring for other gear, the same rinse-and-dry routine applies. See How to Clean Dive Mask: 6 Best Cleaners and Care Products (2026) and How to Clean Dive Boots: A Step-by-Step Guide to Keep Them Fresh for similar care steps.

FAQ

How often should I clean my scuba regulator?

Rinse it after every dive and do a longer freshwater soak at the end of each day of diving. A professional service is generally recommended every year or after a set number of dives, as the manufacturer specifies.

Can I use vinegar to clean my regulator?

No, vinegar and other household cleaners can damage seals and internal parts. Use only cleaners the manufacturer approves, and consult a certified technician if you are unsure.

Should I open the regulator to clean it?

No, do not disassemble the first stage or second stage yourself. Internal servicing should be done by a qualified dive shop technician.

Conclusion

Rinsing, soaking, drying and storing your regulator correctly takes only a few minutes and protects it from salt and grit. Keep the dust caps on, avoid harsh chemicals, and schedule professional servicing as the manufacturer recommends. Consistent care is what keeps your regulator reliable on every dive.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our scuba diving gear guides, checking product details against manufacturer specifications and owner feedback.

About the author

Claire Whitaker
Claire Whitaker

Claire Whitaker writes reviews and buying guides for Scuba Lanai.