I300c Dive Computer Manual: Setup, Settings and Key Functions Explained
Find out where to get the i300c dive computer manual, how to read its display, set up your profile and avoid common mistakes before your next dive.
Updated November 2026
The i300c dive computer manual is the reference that tells you how to set up your unit, read its display and use its dive modes safely. This guide walks you through the parts of the manual that matter most for reef and shore diving: finding the right edition, setting your personal options, and understanding what the screens are telling you underwater. It does not replace the manual, so keep the printed or downloaded copy with your gear.
Find the Correct Manual for Your Unit
Before you read anything, confirm the exact model and firmware on your computer. Manufacturers often revise manuals when firmware changes menu layouts or alarm behavior, so an older edition can point you to buttons or screens that no longer match yours. Check the official manufacturer website for the current download, and note the revision or version number printed on the manual’s cover or last page.
Set Up Your Personal Options Before the Dive
Most of the setup work happens on land, where you have time and a dry table. Work through the settings in this order:
- Set the date and time so your dive log timestamps are accurate.
- Choose your units (metric or imperial) and depth format.
- Set your altitude mode if you dive above sea level. Many manuals list altitude ranges and the matching setting for each.
- Configure the alarms you want, such as maximum depth, ascent rate and no-decompression limit warnings. Use the manual’s default values as a starting point, then adjust them to your own comfort level.
- Select your gas or nitrox setting if your unit supports it, and confirm the oxygen percentage before you descend.
Read the Display During the Dive
Learn the display layout in the manual before you ever wear the unit in the water. Pay attention to the sections that show current depth, dive time, no-decompression time remaining, ascent rate and safety stop prompts. In a dive simulator or a dry run at the surface, cycle through each screen until you can find the information you need within a few seconds. During a real dive, you will want to check depth and remaining time quickly, not hunt through menus.
Respond to Alarms and Warnings
When an alarm sounds, the manual describes what it means and what action the computer expects. Treat every alarm as a prompt to check your depth, ascent rate and time, then act on it. Do not silence a warning and ignore the cause.
Recommended gear
A printed copy of the manual, sealed in a small plastic sleeve, stays useful on a boat or in a dive shop. A dive computer keeper strap also keeps the unit secured to your console during setup and transport.
- A waterproof manual sleeve helps keep the printed guide readable after surface intervals and rinses. View on Amazon
- A dive computer strap keeps the unit from drifting on your wrist or console during the dive. View on Amazon
Common Mistakes
- Using an outdated manual that does not match your firmware or menu layout.
- Skipping the altitude and nitrox settings and assuming the defaults fit your dive.
- Learning the display for the first time at depth instead of on the surface.
- Silencing alarms without checking depth and ascent rate.
- Leaving alarm limits at factory defaults that may not match your training or comfort.
For the broader setup of your full kit, see Scuba Regulator with Dive Computer: 6 Steps to Match and Set Up and Oceanic Dive Mask Computer: 5 Steps to Choose and Set Up for Reef Diving. If you dive with a mask-mounted display, the same basic approach applies to 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).
FAQ
Where can I get the i300c dive computer manual?
Check the official manufacturer website for the current downloadable manual, and match the revision to your unit’s firmware. If you bought from a dive shop, they may also have a printed copy.
Should I change the default alarm settings?
You can adjust them, but start from the manual’s defaults and change only what your training supports. Discuss any changes with your instructor or dive professional.
Can I practice using the computer before a dive?
Yes. Cycle through every screen and menu at the surface until you can find depth, time and ascent information quickly. Consult a dive professional if you are unsure about any setting.
Conclusion
Get the correct manual for your exact unit, set your options before you enter the water, and rehearse the display until it feels routine. A few minutes of preparation makes the computer far easier to read when your attention is on the reef. Consult a qualified dive professional for guidance on settings that affect your dive plan.
Related reading
- Big Blue Dive Light Manual: Step-by-Step Setup and Care Guide
- Zoom Evo Dive Mask: Fit, Features and Buying Tips for Reef Divers
- Zeeporte Dive Full Face Snorkel Mask: Fit, Features and Buying Tips
Ready to choose one?
