How to Reset Suunto Zoop Dive Computer: A Step-by-Step Guide (2026)
Learn how to reset Suunto Zoop dive computer to factory settings, clear the logbook, and prepare it for a new diver. Clear steps and common mistakes covered.
Updated November 2026
Resetting a Suunto Zoop dive computer returns it to its factory settings, which clears custom configuration, personal settings and, depending on the menu path you use, stored dive data. This is useful when you are handing the unit to a new diver, troubleshooting a settings problem, or starting fresh after a rental. Before you begin, confirm what you want to erase, because a reset cannot be undone.
Before You Reset Your Suunto Zoop
Download your logbook first if you want to keep your dive history. Use the Suunto desktop software or the official Suunto app to transfer dives to a computer or phone, then confirm the transfer finished before moving on. Also note your personal settings, such as units, alarms and gas-related preferences, so you can re-enter them after the reset.
Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).
- Fully charged battery, or a fresh battery installed. A low battery can interrupt the reset.
- Your logbook backed up, if you need it.
- The owner’s manual for your exact model, since menu labels vary slightly between Zoop versions.
Steps to Reset the Suunto Zoop to Factory Settings
- Turn the computer off completely. If it is on, hold the mode button until the screen goes dark.
- Press and hold the buttons listed in your manual for the reset sequence. On most Zoop units this involves holding two buttons together while powering the display on.
- Watch for the confirmation prompt on screen. Choose yes to confirm the factory reset when asked.
- Wait for the unit to restart. The display will show the setup screen once the reset is complete.
- Set the date, time and units again, then check that the computer reads the correct battery level.
Checking the Reset Worked
After the reset, go through the main menus and confirm the settings match factory defaults. Check that the logbook is empty if you chose a full reset, and that alarms and units return to default values. If anything looks wrong, repeat the reset with a fresh battery before assuming a fault.
| Check | What to look for |
|---|---|
| Display | Setup screen appears after restart |
| Logbook | Empty if a full reset was done |
| Units and alarms | Back to default values |
| Battery reading | Matches the installed battery |
Common Mistakes
- Skipping the logbook backup and losing dive records you wanted to keep.
- Using a weak or nearly dead battery, which can leave the unit half-reset.
- Following button sequences from a different Suunto model. Check the manual for your exact unit.
- Assuming a reset fixes hardware damage. If the screen stays blank or buttons do not respond, the issue may be physical.
- Forgetting to re-enter personal settings after the reset, which can affect planning and alarms on your next dive.
Recommended gear
A spare battery makes resets and troubleshooting far less stressful, and the correct type is listed in your manual. View on Amazon
A small screwdriver set helps if you need to open the battery compartment cleanly. View on Amazon
FAQ
Will resetting my Suunto Zoop delete my dive log?
A full factory reset typically clears stored dives, so download your logbook first. Confirm the transfer finished before you start the reset.
Do I need to reset the computer after changing the battery?
Usually no. Replacing the battery normally keeps your settings, but check the date and time afterward. If you see errors, a reset may help.
What if the Zoop will not reset?
Try a fresh battery and repeat the button sequence from your manual. If it still will not respond, contact Suunto support or an authorized dealer for service.
For a broader setup walkthrough, see Zoop Suunto Dive Computer: A Step-by-Step Setup and Buying Guide. If the battery is the problem, Suunto Dive Computer Battery Replacement: Step-by-Step Guide for Reef Divers covers the swap in detail.
Conclusion
Resetting a Suunto Zoop is quick once you have backed up your logbook and charged or replaced the battery. Follow the button sequence in your model’s manual, confirm the settings after restart, and re-enter your preferences. If the unit still misbehaves after a clean reset, get it checked before your next dive.
Related reading
- Suunto EON Core Dive Computer: Setup, Use and Buying Tips for Reef Divers
- Suunto Air-Integrated Dive Computer: Setup, Tips and Buying Guide
Ready to choose one?
