Aqualung I770 Dive Computer: Setup, Settings and Reef Dive Tips
Learn how to set up and use the Aqualung i770 dive computer, from initial configuration and gas settings to reading its display on reef and boat dives.
Updated November 2026
The Aqualung i770 dive computer is a wrist-mounted unit designed to track depth, bottom time, ascent rate and no-decompression limits throughout a dive. This guide walks you through the setup steps that matter before your first splash, how to read the display underwater, and a few habits that keep the unit reliable on reef and shore dives. Always confirm your settings against the manufacturer’s manual, since menu layouts and firmware can change.
Before You Start: What to Check on the i770
Start with a few basic checks so the computer is ready when you need it. Charge the battery fully the night before, and make sure the unit is dry and free of salt residue. Rinse it in fresh water after every dive, then let it air-dry out of direct sun.
Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).
- Confirm the battery level and charge fully before travel.
- Inspect the O-ring seals and the buttons for cracks or grit.
- Check that the strap or console mount is secure and not stretched.
- Have your logbook or dive plan open so you can cross-check the computer’s data.
Setting Up Your Personal Profile
Most of the i770’s usefulness depends on the personal settings you enter. Set your units to match what you read on your gauges, and confirm your altitude setting if you dive above sea level. Enter the gas mix you breathe, usually air at the standard 21% oxygen, unless you are diving enriched air.
- Set the measurement units (metric or imperial) and the date and time.
- Choose your gas mix and confirm the oxygen percentage.
- Enter your altitude band if you plan to dive inland or at elevation.
- Set your alarms for maximum depth, ascent rate and bottom time, using conservative values for reef work.
- Save the profile and confirm it shows on the home screen before you pack the unit.
Reading the Display on a Reef Dive
Once you are in the water, the most useful numbers are current depth, bottom time remaining and the no-decompression limit. Glance at the display at regular intervals rather than only when an alarm sounds. On a shore dive where you might descend and ascend several times, keep an eye on the surface interval so you know how the computer is tracking your nitrogen loading.
Pay attention to the ascent rate indicator during your climb. If the arrow or alert shows you are moving too fast, slow down and let the computer reset its guidance. Many divers find that a short safety stop at about 15 feet (5 meters) for three minutes gives them a margin the computer does not require.
Common Mistakes and Tips
- Forgetting to switch the gas mix when you change tanks or diving conditions.
- Leaving the unit in the sun or hot car after a dive, which can affect the battery and display.
- Ignoring a low-battery warning before a multi-day trip.
- Treating the no-decompression limit as a target rather than a ceiling.
- Skipping the post-dive rinse, which lets salt crust form on the buttons.
Recommended gear
A dedicated dive computer mount or console helps keep the unit visible and out of the way of your regulator hose. View on Amazon
A soft silicone protective case reduces scratches on the display during boat loading and shore entries. View on Amazon
A spare battery or charging cable is useful for longer trips where you cannot easily charge between dives. View on Amazon
For a broader view of how computers integrate with other equipment, see Scuba Regulator with Dive Computer: 6 Steps to Match and Set Up, and if you use a dive mask with an integrated display, Oceanic Dive Mask Computer: 5 Steps to Choose and Set Up for Reef Diving covers that setup.
FAQ
How often should I service the Aqualung i770?
Follow the service interval listed in the manufacturer’s manual, and have a certified dive shop check the seals and battery if the unit is used frequently. Regular O-ring inspection is the simplest way to prevent water intrusion.
Can I change the gas mix during a dive?
Changing the gas setting mid-dive is possible on many computers, but confirm the exact procedure in your manual before relying on it. Set the correct mix before you descend whenever you can.
What should I do if the display shows an error?
Note the error message, end the dive safely, and do not rely on the unit until it is checked. Contact the manufacturer or a qualified service technician to diagnose the problem.
Conclusion
With the right setup, the Aqualung i770 gives you clear depth, time and decompression information throughout a dive. Take a few minutes before each trip to check your profile, battery and seals. Consult a qualified dive professional whenever you have questions about your dive plan.
Related reading
- 8 Best Aqualung Mesh Dive Bag Options for Reef and Boat Diving
- Zoom Evo Dive Mask: Fit, Features and Buying Tips for Reef Divers
- Zeeporte Dive Full Face Snorkel Mask: Fit, Features and Buying Tips
Ready to choose one?
