Mares Dive Computer Battery Replacement: Step-by-Step Guide (2026)
Learn how to do a mares dive computer battery replacement safely at home, including tools, seal checks, and when to send it to a service center.
Updated November 2026
A mares dive computer battery replacement is a straightforward job that most divers can handle at home with a few basic tools. This guide walks you through checking the battery type, opening the case, swapping the cell, and resealing the unit so it holds water. You will also learn when a service center is the safer choice.
Check the Battery Type and Warning Signs First
Before you buy anything, confirm what your computer uses. Mares dive computers have historically used replaceable coin-style lithium cells, but the exact size and model depend on your unit, so read the battery designation printed inside the case or in the manual. Signs that the battery is due include a dim or flickering display, a low-battery indicator that appears early, and backlight failure. Replace the battery before a trip rather than on the boat.
Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).
Gather the Right Tools and Supplies
Work on a clean, dry table with good light. Keep the parts organized so nothing gets lost or contaminated with grit.
- The correct replacement lithium cell, fresh from a sealed package
- A small case-opening tool or a thin plastic pry tool (avoid metal that can scratch the housing)
- A small Phillips or Torx screwdriver if your model uses screws in the battery cover
- Lint-free cloth and isopropyl alcohol for cleaning the O-ring groove
- Fresh silicone grease approved for dive equipment
- Replacement O-ring, if the old one is nicked, flattened, or stretched
Replace the Battery and Reseal the Case
Follow these steps in order. Rushing the seal is the most common reason a computer floods later.
- Remove the battery cover or back plate following the manual’s sequence. Note the orientation of the old cell and any contacts.
- Slide out the spent battery and insert the new cell with the polarity matching the old one. Do not bend the contacts.
- Inspect the O-ring. Replace it if you see cuts, flattening, or hardening.
- Clean the O-ring groove and sealing surface, then wipe away all residue.
- Apply a thin, even film of silicone grease to the O-ring. Too much grease can trap debris, so keep it light.
- Seat the O-ring in its groove and close the cover, tightening screws evenly in a cross pattern if your model uses them.
- Power on the unit and confirm the display, date and time, and any settings reset as expected.
Test the Seal Before Your Next Dive
Never assume the case is sealed. Many manufacturers recommend a pressure or vacuum test where available, and some owners report using a dry-box or bag test at home. Check that the unit stays dry after being submerged in fresh water for a few minutes, then inspect the O-ring and interior for moisture. If anything looks wet, stop and do not dive with it. Consult a qualified dive shop or the manufacturer’s service center for further help.
Common Mistakes to Avoid
- Using a battery of the wrong size or chemistry, which can damage contacts
- Reusing a flattened or cracked O-ring to save time
- Applying too much grease, which attracts sand and lint
- Prying with metal tools and scratching the sealing surface
- Skipping the post-install seal test and diving on an unverified unit
Recommended Gear
A good set of small tools and a fresh O-ring kit makes the job much easier. Look for a precision screwdriver set that includes both Phillips and Torx bits, since dive computers often use small fasteners. View on Amazon
Silicone grease formulated for dive gear protects O-rings and keeps them supple. Use a small tube and apply sparingly. View on Amazon
A spare set of O-rings matched to your computer’s case size lets you replace a worn seal without waiting for parts. View on Amazon
FAQ
How often should I replace the battery in my Mares dive computer?
Battery life depends on use, backlight time, and storage conditions. Check the battery indicator before each trip and replace the cell when the display shows low power or behaves erratically.
Can I replace the battery myself without voiding the warranty?
Warranty terms vary by model and region. Check the manual or contact Mares support before opening the case, since some warranties require service center work.
What if my computer floods after I replace the battery?
Stop using it immediately, remove the battery, and let the unit dry in a warm, dry spot. Have a qualified service technician inspect it before any further dives.
Conclusion
A careful mares dive computer battery replacement takes about fifteen minutes once you have the right cell and a clean workspace. The O-ring and seal check matter more than the battery swap itself. When in doubt, have a dive shop or authorized service center handle the work.
Related reading
- Genwiss Dive Light Battery Replacement: Step-by-Step Guide (2026)
- Scuba Regulator with Dive Computer: 6 Steps to Match and Set Up
- Oceanic Dive Mask Computer: 5 Steps to Choose and Set Up for Reef Diving
- Mini Q40 Dive Light Replacement Bulb: Top 5 Picks Compared
Ready to choose one?
