We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Raspberry Pi Dive Computer: A Step-by-Step Build Guide for Beginners

Learn how a raspberry pi dive computer works, what parts you need, and the safety limits to respect before you build or rely on a DIY dive logger.

Updated November 2026

A raspberry pi dive computer is a homemade project that uses a small single-board computer, a pressure sensor and a display to log depth and time during a dive. This guide explains what the build involves, which parts matter, and why a DIY unit should never replace a certified dive computer on a real dive. Read it as an engineering overview, not a guide to life-support equipment.

Understand What a Raspberry Pi Dive Computer Can and Cannot Do

A basic build measures pressure, converts it to depth, and records a timeline. Nearly every commercial dive computer also calculates no-decompression limits, tracks nitrogen loading, and alarms on ascent rate. A Pi-based project typically does none of that reliably, and the gap is where the risk sits. Treat a DIY unit as a data logger for experimentation, not a planning tool.

Shopping for one? See our guide: 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026).

Choose the Core Hardware

Most hobbyist builds start with a Raspberry Pi Zero or Pi 4 board, a waterproof pressure transducer rated for the depth you intend to test, a small OLED or LCD display, and a lithium battery with a protection circuit. The pressure sensor is the critical part. Check its rated range in psi or bar and confirm the housing is pressure-tested well beyond your target depth. Hobby sensors are often rated for shallow water only.

Build and Calibrate the Depth Readout

Work through the build in this order:

  1. Wire the pressure sensor to the Pi’s I2C or SPI pins and confirm raw readings with a test script.
  2. Record the sensor output at surface pressure, then at a known depth in a tank or pool.
  3. Convert pressure to depth using seawater density, roughly 1 meter of depth per 0.1 bar above surface pressure.
  4. Log timestamped depth values to a file at a fixed interval, such as once per second.
  5. Seal the enclosure with O-rings, pressure test it in fresh water, and inspect after every session.

Plan the Enclosure, Power and Testing

Enclosure design causes more failures than software does. Use a commercial dive-rated housing or a machined pressure vessel, never a repurposed food container. Keep the battery in a separate compartment with its own sealed case, since lithium cells are a fire and swelling hazard if punctured or overheated. Test in stages: bench, then fresh-water pool, then shallow open water with a buddy and a certified computer on your wrist for comparison.

Common mistakes

  • Trusting the Pi’s depth output without comparing it to a calibrated gauge.
  • Ignoring the sensor’s temperature drift, which can shift readings by a meaningful margin.
  • Using non-marine-grade O-rings or lubricants that swell or degrade in salt water.
  • Skipping a pressure test after any opening of the housing.
  • Diving with the unit as your only depth or time source.

A certified dive computer gives you the decompression data a DIY build cannot, so use it as your primary instrument.

  • Certified dive computer: provides no-decompression limits and ascent alarms your build will not match. View on Amazon
  • Dive-rated O-ring kit: keeps any housing seal intact and replaceable. View on Amazon
  • Dive depth gauge: offers an independent reference for checking your prototype’s readings. View on Amazon

For how a dedicated unit should be set up with your regulator, see Scuba Regulator with Dive Computer: 6 Steps to Match and Set Up. If you prefer a computer built into your mask, Oceanic Dive Mask Computer: 5 Steps to Choose and Set Up for Reef Diving covers that route.

FAQ

Is a raspberry pi dive computer safe to use on real dives?

Not as a primary instrument. A DIY unit lacks validated decompression algorithms and independent safety checks. Use it only as an experimental logger alongside a certified computer.

How accurate is a DIY depth reading?

Accuracy depends on the sensor, calibration and temperature compensation. Verify it against a calibrated gauge before trusting any reading.

Do I need training to build one?

The electronics require basic programming and wiring skill. For any use in the water, consult a qualified dive professional before diving with homemade equipment.

Conclusion

A raspberry pi dive computer can teach you how pressure sensing and data logging work. Build it carefully, test it in stages, and keep a certified computer as your decision-making tool. Consult a dive professional before relying on any homemade gear underwater.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our scuba diving gear guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Scuba Lanai.