We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Dive Computer Mares Smart: Setup, Settings and Tips for Reef Dives

Learn how to set up and use a dive computer Mares Smart on reef dives, from pairing and gas settings to safety stops and common mistakes to avoid.

Updated November 2026

A dive computer Mares Smart is a wrist-worn dive computer that tracks depth, time, and decompression status throughout your dive. This guide walks you through the basic setup, the settings worth checking before you enter the water, and the habits that keep your readings reliable on reef and shore dives. Work through it before your next trip and you will spend less time fiddling with the unit and more time watching fish.

Before You Start: Check the Basics

Start by reading the manufacturer’s manual from front to back, especially the sections on alerts and safety stops. Charge the unit fully the night before a dive day, because a low battery is an avoidable distraction at depth. Confirm the firmware version and update it only from the official Mares source, following the steps in the manual.

Setting Up the Mares Smart Dive Computer Step by Step

Most of the setup happens in the menu, and it takes about ten minutes if you go in order. Set your units (metric or imperial), date, and time first, so your dive log records accurately. Then move on to the dive-specific settings, which matter far more than the clock.

  1. Select your units for depth, temperature, and pressure.
  2. Set your altitude mode if you dive above sea level. Most Hawaiian and Caribbean dives use the sea-level setting.
  3. Choose your gas mix. For air, leave the oxygen percentage at 21 percent unless you are trained and equipped for enriched air.
  4. Enable the safety stop reminder and set it to the depth your agency teaches, commonly 15 feet (5 meters) for three minutes.
  5. Set your alarm thresholds for maximum depth and ascent rate. Many divers keep the ascent alarm on from the first dive.
  6. Check the low-air or tank pressure input if your model supports a transmitter, and confirm the readout appears correctly.

Using the Dive Computer on the Surface and Underwater

Before the first descent, let the unit complete its surface interval check and confirm your no-decompression limit. Keep your eyes on the depth and time, not only the total dive time. Ascend slowly, watching the ascent rate indicator, and stop at your safety stop even if the computer does not require one. The computer gives you data, but your buddy and your training make the final call.

Planning Repetitive Dives

After each dive, the unit shows a residual nitrogen indicator. Respect the surface interval it recommends before your next dive. On a multi-dive day, treat the computer’s no-stop time as a ceiling rather than a target, and plan shallower second dives when your nitrogen load is high.

Common Mistakes to Avoid

  • Forgetting to set the gas mix, which can throw off your decompression calculations.
  • Diving with a low battery, which leaves you without data for the ascent.
  • Ignoring the ascent rate alarm and surfacing too fast.
  • Skipping the safety stop when the computer does not prompt it.
  • Mixing the computer with a different unit’s settings without rechecking them.

A reliable dive computer pairs well with a sturdy wrist mount, so the screen stays visible when you check your depth. A spare battery or charging cable is also worth keeping in your dive bag. A small dive slate helps you record readings and notes between dives.

  • Dive computer wrist strap for a secure, adjustable fit on the wrist. View on Amazon
  • Dive slate with pencil for logging surface intervals and dive notes. View on Amazon
  • Dive bag with separate compartments to keep electronics protected in transit. View on Amazon

If you are choosing a mask to pair with your computer, read Oceanic Dive Mask Computer: 5 Steps to Choose and Set Up for Reef Diving for fit tips. For a broader comparison of computer-equipped masks, see 4 Best Dive Masks with Computer for Reef Divers: Picks Compared (2026). If your regulator and computer are being set up together, Scuba Regulator with Dive Computer: 6 Steps to Match and Set Up covers the connection process.

FAQ

Do I need to update the firmware on my Mares Smart dive computer?

Firmware updates can fix bugs and improve performance, so check the official Mares site periodically. Follow the manufacturer’s instructions exactly, and do not install updates from unofficial sources.

Can I use the Mares Smart computer for nitrox diving?

Whether your unit supports enriched air depends on the model and its configuration. Check the manual for oxygen percentage settings, and confirm you hold the appropriate certification before diving nitrox.

What should I do if the computer shows a decompression warning?

Ascend immediately to your safety stop depth and follow the computer’s guidance. Stop, breathe, and make a safe ascent with your buddy. If you have any symptoms after surfacing, seek medical attention and consult a dive medicine professional.

Conclusion

Setting up a dive computer Mares Smart takes a few careful minutes, but the payoff is reliable data on every dive. Set your gas mix, alarms, and units before you enter the water, and keep the battery charged. Treat the computer as a tool that supports your training, and check the manual or a dive professional whenever a reading is unclear.

Miles Sinclair

About Miles Sinclair

Miles Sinclair is part of our editorial team and reviews and edits our scuba diving gear guides, checking product details against manufacturer specifications and owner feedback.

About the author

Miles Sinclair
Miles Sinclair

Miles Sinclair writes reviews and buying guides for Scuba Lanai.